We’re within the midst of somewhat laundry room refresh and I’ve been slowly finishing initiatives to replace this area. We completed it nearly 7 years in the past and it’s some of the used rooms in our house (after the kitchen). However now that we now have 3 kiddos and my model has developed it’s time for some modifications! My most up-to-date venture was constructing a shelf with a wooden gallery rail and I’m right here to share all the small print with you!
Once we first accomplished the laundry room, we put a shelf on the wall above the washer and dryer that was round 5′ lengthy. I do not know why I made a decision on that size or why I didn’t lengthen all of it the best way throughout the wall. It was early in my design journey and the laundry room was the primary room I ever designed from prime to backside!
The extra I checked out it, it simply appeared unbalanced and there was extra room for added storage and performance. So I got here up with the concept to create a shelf with a wooden gallery rail on prime and a dangling brass rail on the underside.
I used to be impressed to create the wooden gallery rail after making a pet food holder for Oakley out of bigger wooden spindles. Brass gallery rails have change into tremendous widespread in design – we now have one in our kitchen and I adore it – however I wished to place a special spin on it. Numerous older antiques have this aspect which is such a lovely element, and I wished to do it in a extra trendy means that match my model higher.
SUPPLIES FOR SHELF WITH A WOOD GALLERY RAIL
STEP 1
Drill the holes on your finials. You’ll wish to measure out your spacing first – I spaced mine 2.5″ other than each other however you are able to do no matter appears to be like finest to you! I positioned them about 1/2″ from the entrance fringe of the board.
To drill the holes I used a 5/8″ drill bit. You can additionally use a spade bit however since these have a sharp finish, I didn’t wish to danger drilling by the wooden!
STEP 2
Trim the highest a part of the finials off. It was pretty simple to drill into the shelf board, however drilling into the nook spherical could be actually tough. So to keep away from this, I simply trimmed off the highest a part of the finials in order that the nook spherical might sit flat.
I used the band noticed to do that and it was so fast and straightforward! If wanted, you may then sand down the tops for a totally clean floor.
STEP 3
Reduce and miter your nook spherical. It helps to put your finials within the holes to get a greater concept of the place the nook spherical will sit. Then you should use your mitre noticed set at a forty five° to chop each bit.
STEP 4
Drill the holes in your corbels. When you’ve got a drill press that’s the best means to do that, however we don’t so I used some clamps and my common drill. The copper pipe I used for the “brass rail” is 1/2″ and I used a 5/16 spade bit for the holes.
I stained my corbels first, however I recommend drilling first after which staining!
Begin by clamping two corbels collectively. Be sure that they’re aligned the correct means (ie. the brackets on the again are going through the identical means). Eye ball the middle space of your corbel the place you need the pipe to go and drill down as straight as you may by each corbels.
When you’ve executed the primary two, take one in every of them and place it on prime of a non drilled corbel. Use this as a template to drill into the one beneath. Repeat till all corbels have been drilled by.
STEP 5
Now that each one your wooden is lower and prepared it’s time to stain. I used a wooden conditioner first which helps to remove splotching and offers you a pleasant even end. You may apply this with a black foam brush.
Then I used my favourite Darkish Walnut Gel Stain to stain every part. I used a staining pad for the precise shelf and corbels after which used a small craft paint brush for the finials. Then I wiped the finials off on a rag to take away the surplus.
STEP 6
As soon as the stain is dry, apply a prime coat. I used Common Finishes Excessive Efficiency High Coat in Satin and solely did one coat since this isn’t going to get a number of motion ?
STEP 7
Reduce your copper pipe. Earlier than you narrow, measure out the size you want by putting the 2 finish corbels on the wall. This will provide you with a extra exact measurement however you do have some wiggle room for the reason that pipe will sit an inch or so into the corbels.
We determined to have the pipe go right through all 5 corbels in a single piece however you could possibly additionally lower the pipe into sections and have the seams be hidden inside the corbels.
Slicing copper pipe is tremendous simple with this little pipe cutter you may get on the house enchancment retailer.
STEP 8
Spray paint your pipe. I used this gold leaf spray paint after which this clear coat on prime of that.
STEP 9
Create your wooden gallery rail! Glue your finials into the holes you drilled after which glue the nook spherical on prime. This DAP Speedy Fuse glue is my favourite. It dries tremendous fast and is so sturdy!
STEP 10
Grasp your shelf! Pull the pipe by the corbels and hook the corbels onto the screws within the wall. We had been ready to make use of among the present holes that had been there already after which needed to drill new holes on both finish. To drill into tile, simply ensure you use a masonry bit!
We had somewhat bother getting all 5 corbels to slip into BOTH screws for each so we ended up solely utilizing one screw per corbel and it was nonetheless tremendous sturdy.
STEP 11
Spray paint your hooks to match the pipe. No matter coloration you spray your pipe, ensure you use the identical on your hooks in the event that they aren’t a very good match. I used these bathe hooks and love the little ball element they’ve.
Now it’s the enjoyable half – time to embellish and revel in your shelf!
This wooden gallery rail shelf feels SO significantly better than the unique one did on this area. I like that it fills up the entire size of the wall and has the extra brass rail beneath to hold issues from. It’s additionally rather a lot prettier and added a beautiful contact of attraction and character to our laundry room.
What do you assume? Would you construct your individual shelf with a wooden gallery rail?
Associated
